| ADA-Compliant Showers | WR 6030 | WR 3636 | WR 1939 | WR 3939 | FW 44/5 |
Specifications for Models: WR 1939, WR 1939-A, WR 1939-B, WR 1939-C, WR 3939, WR 3939-A, WR 3939-B, WR 3939-C
Warm Rain models WR 1939 (1-piece) & WR 3939 (3-piece remodeler) bath fixture are constructed of reinforced polyester resin covered with a high gloss gel-coat of 18-20 mil. thickness. The reinforced fiberglass includes alumina tri-hydrate fire retardant and a minimum content of 18% fiberglass.
The bottom base of the unit is constructed of 1/2" end-grained balsa wood sandwiched between 2 layers of reinforced fiberglass at a content no less than 18%. The base is an intergral part of the unit.
The unit will measure 38 ½" L x 39 1/2" W x 77 1/2" H and has a textured bottom floor
These units are reinforced for the future installation of grab bars & a fold-up seat. The reinforcement is shown in the diagram below.
MaxGuard® AB gel-coat with Microban® antibacterial additive is an option for this unit.
These Warm Rain Transfer showers arrive on site fully tested, inspected, and certified to meet or exceed the precise standards established by the FHA/HUD, materials bulletin 73), American National Standards Z-124.1 and Z-124.2, ASTM/E-84, and is certified by the NAHB (National Association of Home Builders).
(More Model Option Specifications)
WR-1939-A & WR 3939-A: Models includes Grab Bars
The grab bars will be factory installed. The grab bars will be 1 1/2" outside diameter ADA compliant stainless steel bars. There are 3- 24" horizontal grab bars The wall reinforcement is 1/2" plywood fiberglassed into the unit. 1-24" grab bar on the wet wall will be placed 34.5" above the floor. 1-24" grab bar on the back wall will be placed 34.5" above the floor. 1-24" grab bar will be placed opposite the wet wall at 34.5" above the floor.
WR 1939-B & WR 3939-B: Models includes Grab Bars & Fold-up Seat
The grab bars will be factory installed. The grab bars will be 1 1/2" outside diameter ADA compliant stainless steel bars. There are 2- 24" horizontal grab bars. The wall reinforcement is 1/2" plywood fiberglassed into the unit. 1-24" grab bar on the wet wall will be placed 34.5" above the floor. 1-24" grab bar on the back wall will be placed 34.5" above the floor. The ADA compliant seat will be factory installed. The seat will support a minimum of 250#’s. The wall reinforcement is 1/2" CDX plywood fiberglassed into the unit. The seat will be placed on the side wall opposite the controls 18" above the floor & cover the full depth of the stall. The seat is an "L" shaped phenolic white ADA compliant seat.
WR 1939-C & WR 3939-C: Models includes Grab Bars, Fold-Up Seat, Pressure Balance Valve, Hand held Shower with Slide Bar, Vacuum Breaker, & Curtain Rod with Hangers
The grab bars will be factory installed. The grab bars will be 1 1/2" outside diameter ADA compliant stainless steel bars. There are 2- 24" horizontal grab bars The wall reinforcement is 1/2" plywood fiberglassed into the unit. 1-24" grab bar on the wet wall will be placed 34.5" above the floor. 1-24" grab bar on the back wall will be placed 34.5" above the floor. The ADA compliant seat will be factory installed. The seat will support a minimum of 250#’s. The wall reinforcement is 1/2" CDX plywood fiberglassed into the unit. The seat will be placed on the side wall opposite the controls 18" above the floor & cover the full depth of the stall. The seat is a "L" shaped phenolic white ADA compliant seat. 1-Symmons Temptrol Valve & Kit model # S-25-300-B30-V-X-2000 will include a Temptrol 2000 pressure balance valve, Hand held shower with 30" bar, Vacuum breaker. Also, 1-Seachrome 5’ Curtain rod with hangers will be included with the unit.
MaxGuard® is a registered trademark of the Neste Corporation, Espoo, Finland
Microban® is a registered trademark of Microban Products Company, Huntersville, NC
Warm Rain is a registered trademark of the Great Lakes Plastics Corporation, Hancock, MI
Warm Rain Corporation
P.O. Box 600 Hancock, MI 49930
Voice: 906-482-3750
Fax: 906-482-2585
E-mail: tedk@warmrain.com